The Art of-Mastering-Exploring Plumbing Fundamentals-Basic Plumbing for Installing a Bathtub-When You Install a Bathtub
The Art of-Mastering-Exploring Plumbing Fundamentals-Basic Plumbing for Installing a Bathtub-When You Install a Bathtub
Blog Article
This great article down below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is really entertaining. Check it out for yourself and see what you think about it.
Mounting a bath tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult job. If the old tub is readily obtainable, the task can relocate quickly; if you need to open up a wall surface to remove the old bathtub as well as place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually certified on your own for the work as well as fit trying it. Instead of employing a professional to take control of a halfway-completed job, it is better to consider employing one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This post will aid you install a brand-new bathtub in your shower room if you have already acquired a new tub and do not require to change the plan of your previous supply of water pipes.
Your devices and also product checklist need to consist of the following:
Getting ready for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to avoid strain on the tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly problematic as a result of the limited access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Using both wooden boards under its feet, put the tub in the needed setting. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the level checks out level.
To set up faucets, fit all-time low of the outermost flexible faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the water system and also examine all joints as well as new pipework for leaks and also tighten them if essential. Load the bath tub as well as also inspect the overflow outlet and also the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the tub should wait up until the tub has been made use of at least once as this will certainly settle it right into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place in between the tap and the sink. Secure the faucet in position with the maker provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet ports. The former type needs to be linked to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to fracture an inflexible seal, triggering the water to pass through the wall between the bath as well as the tiling, leading to complications with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes and cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to permit the movement experienced when the tub is in use. The sealer can split rather early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that write up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing research the internet. Sharing is caring. Helping others is fun. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Need quality service? Report this page